For a #8 screw in hardwood, published guidance falls at 7/64 inch or 1/8 inch, depending on the procedure and bit type. Start with your screw's or project's own instructions. If you don't have those, use a chart entry that matches your screw size, hardwood, and bit style.
Then drive the actual screw into a matching hardwood offcut before you drill the cabinet. A clamped workpiece and a straight hole drilled to the right depth give the screw a predictable path.

What Pilot-Bit Size Should You Start With?
Look first at the fastener packaging, cabinet hardware instructions, or project plan, since that size is tailored to your screw and joint. Without manufacturer guidance, match your bit to three details: the screw gauge, hardwood material, and straight versus tapered bit style. A general chart only helps when all three match your specific setup.
Two published #8 references show why one size doesn't cover every case. WOOD Magazine's 7/64-inch #8 pocket-screw example applies to its no-jig pocket-screw procedure. That article says you need pilot holes for dense wood or for conventional screws. The McFeely's #8 straight-bit hardwood chart entry lists 1/8 inch. That chart gives separate rows for shank holes, hardwood and softwood pilots, and different bit types, so read the row that fits your bit.

The softwood figures in the same sources show how much the wood category matters. WOOD Magazine's procedure calls for a 3/32-inch pilot in softwood for the same #8 screw, which is smaller than its hardwood size. The McFeely's chart lists 7/64 inch for a #8 straight pilot in softwood. It also lists 11/64 inch as the #8 screw shank hole size. That hole is for the part the screw passes through, not the pilot hole in the receiving piece. If you read across the wrong row, you can end up with a bit that's far too large for the threads to grip.
These values come from different contexts. Don't average them into a rule, and don't treat either one as a spec for an unknown cabinet screw. A practical approach is to pick the size from the source closest to your setup: the WOOD figure if you're doing that kind of pocket-screw joint, or the McFeely's figure if you're using a straight bit with a conventional #8 wood screw. Confirm it in scrap before you trust it. If the screw binds, won't bite, or feels loose in the test hole, stop. Check the instructions or chart again before you drill the real part.
Why drill a pilot hole at all? The bit removes some of the wood the screw's threads would otherwise have to push aside. That can make driving easier and may reduce the wedging that splits hardwood. It's a reasonable explanation, but a pilot hole won't prevent splitting every time, which is another reason to test first.
Test the Fit and Drill a Straight, Depth-Controlled Hole
Use the bit you picked in the section above and the exact screws you plan to install:
- Test in matching scrap. Drill a hole in an offcut of the same hardwood and drive the actual screw. It should go in steadily and pull up snug. If it jams, cracks the offcut, or spins without holding, go back to your size choice before touching the cabinet.
- Clamp the cabinet stock. The work should not move when you push on the drill. In its pocket-screw method, WOOD Magazine's clamped positioning block stops the workpiece from sliding during assembly. In that procedure, the block stays clamped while the shank hole guides the pilot-hole bit into the undrilled workpiece. Clamping any part you're drilling serves the same purpose.
- Mark the center precisely. Make a small dent at each screw location so the bit tip has a place to seat.
- Line the bit up with the screw's path. Hold the drill square to the surface unless the joint calls for an angle. If you have trouble keeping it square, use a drilling guide.
- Set the depth. Wrap tape around the bit or add a stop collar at the depth the screw will reach. That also keeps you from drilling through a visible face. Don't borrow depths from someone else's joint. Use the length of your screw and the thickness of your parts.
- Drill, then drive. Back the bit out to clear chips, check that the hole is clean, and drive the screw at a steady speed. If you need help choosing a driver, our guide to screwdriver types and uses explains the options. For low-torque assembly work, see our article on electric screwdriver torque settings.
FAQs
Can I use straight-bit and tapered-bit pilot sizes interchangeably?
No. Use the chart row for the bit you actually own. McFeely's explains that tapered bits drill the body hole and the pilot hole in a single pass. A diameter listed for a straight bit doesn't describe a tapered bit's profile.
How do I keep the bit from wandering in heavy grain?
An awl or nail can slide off your mark when the grain is heavy. WOOD Magazine recommends a concave nail-set tip instead. You tap a 1/32-inch nail set with a small hammer, and the concave tip stays aligned regardless of the grain. That makes it easier to seat the bit right on the mark.
Can a tapered pilot hole be too deep or too shallow?
Yes. McFeely's tapered-bit depth warning says a hole that's too deep leaves the threads nothing to grip, and one that's too shallow can jam the screw. Set a stop at the depth your screw will reach and check it in scrap first.
Do I need a pilot hole if I'm using special pocket-hole screws?
Maybe not. WOOD Magazine says special pocket-hole screws can go straight into most woods. It calls for pilot holes when the wood is dense or when you're using conventional screws. With hard cabinet stock, test one screw without a pilot in scrap. If it splits the wood or fights you, drill a pilot.














































Leave a comment
This site is protected by hCaptcha and the hCaptcha Privacy Policy and Terms of Service apply.