Fanttik vs HOTO Electric Screwdriver: How to Compare Them Fairly

Short answer: pick by torque range, not by badge. If you open cameras and watches, the Fanttik E1 MAX is the match. For mixed electronics with more torque steps, take the E2 Ultra. For furniture and cabinet assembly, the S2 Pro is the only one of the three that reaches 8 N.m.

HOTO and Fanttik both sell cordless and precision electric screwdrivers, so the two names turn up side by side in search. This guide publishes the verified Fanttik numbers in full and gives you a neutral checklist to hold any competing model against, rather than quoting specs for a product we do not manufacture.

Quick Answer: the three Fanttik screwdrivers compared here

Fanttik's electric screwdriver line splits in two. The E series is precision — pen-shaped bodies, torque in fractions of a newton-metre, aimed at electronics. The S series is household — cordless power, torque running from half a newton-metre up, aimed at assembly. Almost every "which one" question resolves once you know which side of that line your work sits on. The full range is wider than the three models below (the E series also includes the E1, E1 PRO and E2 MAX; the S series the S1 Pro and S2 Pro Max), but these three cover the precision, mid-range and household cases people usually weigh up.

Spec	Fanttik E1 MAX	Fanttik E2 Ultra	Fanttik S2 Pro
Torque Modes	2 Gear 0.05 / 0.2 N.m	5 Gear 0.05/0.1/0.2/0.4/0.6 N.m	7 Gear 0.5/1/2/3/4/5/6/8 N.m
Suitable for	Camera / Watch / Precision Repair	Small Appliances / PC / RC Car	Furniture Install / PC Repair
S2 Magnetic Bits	50	50	20
Speed	200 RPM	270 RPM	250 RPM
Battery Capacity	350 mAh	800 mAh	2000 mAh + 5V/1A Charging
LED Lights	Yes	Yes	Yes
Tool Type	Electric	Electric	Electric
Storage Type	Aluminum Alloy Magnetic Case	Rotatable Magnetic Case	Premium Magnetic Storage Box
Price (at time of writing)	$59.97	$69.99	$79.99

The differences that actually matter

1. Torque floor and ceiling define the job

The E1 MAX and E2 Ultra share the same 0.05 N.m floor, the setting that lets you drive a screw into a camera body or a watch back plate without stripping the thread. Where they part company is the ceiling and the granularity: the E1 MAX offers two gears (0.05 and 0.2 N.m), while the E2 Ultra spreads five gears from 0.05 up to 0.6 N.m. That extra headroom is what makes the E2 Ultra comfortable on small appliances, PC internals and RC car chassis screws.

The S2 Pro starts at 0.5 N.m — roughly where the E2 Ultra runs out — and climbs through seven gears to 8 N.m. That is a different class of fastener entirely: flat-pack furniture bolts, cabinet hinges, wall brackets. Running a driver with an 8 N.m ceiling on a laptop screw is how cases crack, which is why Fanttik keeps the two families separate instead of selling one "does everything" tool.

2. Bit count is not the same as bit coverage

The E1 MAX and E2 Ultra each list 50 S2 magnetic bits; the S2 Pro lists 20. That is not a downgrade — household fasteners come in far fewer head types than consumer electronics do, so a 20-bit set covers the S2 Pro's use case while a precision repair kit needs pentalobe, tri-point, torx security and Y-type profiles just to open modern devices. When you compare any two brands, count the bit profiles relevant to your work, not the number printed on the box. Our screwdriver replacement bits guide covers the Fanttik bit standards and how to reorder them.

3. Battery capacity tracks the workload, not the price tier

The E1 MAX carries a 350 mAh cell, the E2 Ultra 800 mAh, and the S2 Pro 2000 mAh with 5V/1A charging. Bigger is not automatically better here: a precision driver idles between careful turns, so the 350 mAh cell is sized for that duty cycle and keeps the barrel thin enough to hold like a pen. The S2 Pro needs its 2000 mAh pack because driving 4 N.m fasteners through chipboard is continuous, high-draw work.

4. Case and handling separate the two E models

The E1 MAX stores in an aluminum alloy magnetic case; the E2 Ultra uses a rotatable magnetic case, and the S2 Pro comes in a premium magnetic storage box. Both E models list a pry bar and tweezers as equipped tools and both support a Power / Manual working mode, so you can finish a screw by hand when the last quarter-turn needs feel rather than a motor. The S2 Pro's spec sheet instead lists a 90° angle adapter and an extended rod — accessories that matter when you are reaching into a cabinet corner, not into a phone.

5. What we will and will not say about HOTO

HOTO is a consumer tool brand whose catalogue overlaps ours in several categories, which is why the two names turn up in the same searches. What we deliberately do not do on this page is publish HOTO's torque figures, battery capacities, bit counts or prices: we cannot verify them from our own bench, and a table built on second-hand numbers is worse than no table at all. Check the current figures on HOTO's own listing before you decide.

Instead, use this five-point checklist against whichever competing model you are considering, including HOTO's:

• Lowest torque setting — for electronics repair the floor matters more than the ceiling; Fanttik's E-series floor is 0.05 N.m, so use that as your reference point when reading a rival spec sheet.
• Number of torque gears — two gears is fine for a single job type; five or more lets one tool cover several.
• Bit standard and profiles — check the shank standard and whether the security profiles you actually need are in the box.
• Manual mode — can you finish or start a screw by hand without swapping tools?
• Charging port — USB-C means one cable for everything; anything proprietary is a cable you will lose.

Which One Should You Buy?

Buy the E1 MAX if your work is cameras, watches, electronic bracelets and other genuinely small mechanisms, and you want the same 50-bit set as the E2 Ultra at the lowest price of the three ($59.97). Two torque gears is enough when every screw on your bench is in the same size class.

Buy the E2 Ultra if your repairs range across phones, laptops, small appliances and RC hardware. The five-gear spread from 0.05 to 0.6 N.m and the 800 mAh cell are what you are paying the extra over the E1 MAX for, along with a faster 270 RPM drive.

Buy the S2 Pro if the words "flat-pack" or "cabinet" appear anywhere in your plans. Its 0.5–8 N.m range, 2000 mAh battery, 90° angle adapter and extended rod are built for assembly, and it will not help you at all inside a phone.

Buy two if you do both. An E-series driver plus the S2 Pro is the honest answer for anyone who repairs electronics and builds furniture.

FAQ

Is Fanttik or HOTO better for electronics repair?

Judge it on the torque floor. Fanttik's E1 MAX and E2 Ultra both start at 0.05 N.m with S2 steel magnetic bits and a manual working mode, which is the specification set that matters for opening phones, cameras and laptops. Compare any competing model's lowest torque setting and bit profiles against those figures before deciding.

What is the difference between the Fanttik E series and S series?

The E series is precision: a 0.05 N.m torque floor, pen-shaped body and precision bits, aimed at electronics — bit counts vary by model, with the E1 MAX and E2 Ultra at 50. The S series is household: the S2 Pro runs 0.5 to 8 N.m with a 2000 mAh battery, a 90° angle adapter and an extended rod, aimed at furniture installation and general assembly. The two families do not overlap in torque range, so they are not upgrades of one another.

Do Fanttik and HOTO also come up together on rotary tools and car vacuums?

Those categories overlap in search too, so the same rule applies: read each brand's own spec sheet rather than a third-party summary. On the Fanttik side the rotary tools are the F2 Master (3/32" collet, 35-piece accessory kit) and the F2 Pro (1/8" collet, 55-piece kit) — the 1/8" collet is the common standard that accepts widely available generic accessories. The car vacuum line includes the Slim V10 APEX, whose suction power is rated 19 kPa / 10 kPa. As with the screwdrivers, compare the published specs of each side directly rather than relying on brand reputation.

Which Fanttik screwdriver has the most bits?

The E1 MAX and E2 Ultra tie at 50 S2 magnetic bits each — as does the E2 MAX, the other 50-bit model in the precision range. The S2 Pro lists 20, which is the appropriate count for household fastener heads. Replacement and add-on bits are covered in the support guide linked below.

Related Guides

• Fanttik E2 Ultra manual — torque gear selection and charging
• Fanttik S2 Pro manual — angle adapter and extended rod setup
• Screwdriver replacement bits — what is in each kit and how to reorder
• Fanttik user manual PDF hub — every product manual in one place